Fixed accelaration values for old profiles and filaments

- Fixed accelaration values for old profiles
- Add new filament features
- Add new filament
- Add lithophane profile for 0.6mm volcano nozzle

PrusaSlicer/filament/ColorFabb nGen Volcano.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-07-18 at 16:41:54
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-16 at 23:20:59 UTC
 bed_temperature = 90
 bridge_fan_speed = 100
 compatible_printers = 
@@ -17,6 +17,7 @@ filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cost = 21.2
 filament_density = 1.2
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
@@ -25,6 +26,15 @@ filament_max_volumetric_speed = 24
 filament_minimal_purge_on_wipe_tower = 15
 filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 1.4
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
 filament_settings_id = ""
 filament_soluble = 0
 filament_toolchange_delay = 0
@@ -32,6 +42,7 @@ filament_type = NGEN
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
+filament_wipe = nil
 first_layer_bed_temperature = 85
 first_layer_temperature = 240
 inherits = ColorFabb nGen
@@ -40,4 +51,4 @@ min_fan_speed = 35
 min_print_speed = 15
 slowdown_below_layer_time = 20
 start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}24{else}45{endif} ; Filament gcode"
-temperature = 230
+temperature = 240

PrusaSlicer/filament/ERYONE PLA Volcano.ini

@@ -0,0 +1,54 @@
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-20 at 18:36:17 UTC
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #FF3232
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 19
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 25
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_wipe = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
+inherits = Generic PLA
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 20
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and nozzle_diameter[0]==0.6}18{elsif printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and nozzle_diameter[0]==0.4}30{elsif printer_notes=~/.*PRINTER_FULLMODEL_ENDER3_DD_06.*/}0.04{else}0{endif} ; Filament gcode"
+temperature = 215

PrusaSlicer/filament/Generic PET.ini

@@ -1,8 +1,10 @@
-# generated by Slic3r Prusa Edition 1.40.1+win64 on 2018-08-21 at 04:44:31
+# generated by PrusaSlicer 2.0.0+win64 on 2019-08-09 at 19:59:43
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
+compatible_prints = 
+compatible_prints_condition = 
 cooling = 1
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
@@ -10,18 +12,26 @@ extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 20
 filament_colour = #FF8000
-filament_cost = 0
-filament_density = 0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 27.82
+filament_density = 1.27
 filament_diameter = 1.75
+filament_load_time = 0
 filament_loading_speed = 28
+filament_loading_speed_start = 3
 filament_max_volumetric_speed = 8
-filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "List of manufacturers tested with standard PET print settings:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladec PETG"
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
 filament_settings_id = ""
 filament_soluble = 0
 filament_toolchange_delay = 0
 filament_type = PET
+filament_unload_time = 0
 filament_unloading_speed = 90
+filament_unloading_speed_start = 100
 first_layer_bed_temperature = 85
 first_layer_temperature = 230
 inherits = Generic PET

PrusaSlicer/filament/Generic PET Volcano.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-12 at 02:31:59
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-17 at 03:40:09 UTC
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
@@ -17,21 +17,32 @@ filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cost = 27.82
 filament_density = 1.27
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
 filament_max_volumetric_speed = 24
 filament_minimal_purge_on_wipe_tower = 15
-filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
+filament_notes = "List of manufacturers tested with standard PET print settings:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladec PETG"
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 1.4
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
 filament_settings_id = ""
 filament_soluble = 0
 filament_toolchange_delay = 0
-filament_type = PET
+filament_type = PETG
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
+filament_wipe = nil
 first_layer_bed_temperature = 85
 first_layer_temperature = 230
 inherits = Generic PET

PrusaSlicer/filament/HDGlass PETG Volcano.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-12 at 02:31:53
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-17 at 03:40:18 UTC
 bed_temperature = 75
 bridge_fan_speed = 50
 compatible_printers = 
@@ -17,6 +17,7 @@ filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cost = 39
 filament_density = 1.27
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
@@ -25,13 +26,23 @@ filament_max_volumetric_speed = 24
 filament_minimal_purge_on_wipe_tower = 15
 filament_notes = HDGlass
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 1.4
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
 filament_settings_id = ""
 filament_soluble = 0
 filament_toolchange_delay = 0
-filament_type = PET
+filament_type = PETG
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
+filament_wipe = nil
 first_layer_bed_temperature = 70
 first_layer_temperature = 220
 inherits = Generic PET Volcano

PrusaSlicer/filament/PrimaSELECT PETG Volcano.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-12 at 02:31:47
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-17 at 03:40:22 UTC
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
@@ -17,6 +17,7 @@ filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cost = 25
 filament_density = 1.27
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
@@ -25,13 +26,23 @@ filament_max_volumetric_speed = 24
 filament_minimal_purge_on_wipe_tower = 15
 filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nprimaSELECT PETG"
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 1.4
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
 filament_settings_id = ""
 filament_soluble = 0
 filament_toolchange_delay = 0
-filament_type = PET
+filament_type = PETG
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
+filament_wipe = nil
 first_layer_bed_temperature = 80
 first_layer_temperature = 220
 inherits = Generic PET Volcano

PrusaSlicer/filament/Prusament PETG 0.6 nozzle Volcano.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-12 at 02:31:39
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-17 at 03:39:37 UTC
 bed_temperature = 90
 bridge_fan_speed = 50
 compatible_printers = 
@@ -17,6 +17,7 @@ filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cost = 24.99
 filament_density = 1.27
+filament_deretract_speed = nil
 filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
@@ -25,13 +26,23 @@ filament_max_volumetric_speed = 24
 filament_minimal_purge_on_wipe_tower = 15
 filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 1.4
+filament_retract_lift = 0.2
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
 filament_settings_id = ""
 filament_soluble = 0
 filament_toolchange_delay = 0
-filament_type = PET
+filament_type = PETG
 filament_unload_time = 0
 filament_unloading_speed = 90
 filament_unloading_speed_start = 100
+filament_wipe = nil
 first_layer_bed_temperature = 85
 first_layer_temperature = 240
 inherits = Prusament PETG 0.6 nozzle

PrusaSlicer/print/0.04mm ULTRA DETAIL Ender3.ini

@@ -1,7 +1,7 @@
 # generated by Slic3r Prusa Edition 1.40.1+win64 on 2018-08-21 at 02:50:05
 avoid_crossing_perimeters = 1
 bottom_solid_layers = 20
-bridge_acceleration = 300
+bridge_acceleration = 1000
 bridge_angle = 0
 bridge_flow_ratio = 0.8
 bridge_speed = 20
@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 25%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 20
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.05mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.06mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.08mm VERY DETAIL Ender3.ini

@@ -1,7 +1,7 @@
 # generated by Slic3r Prusa Edition 1.40.1+win64 on 2018-08-21 at 02:49:33
 avoid_crossing_perimeters = 1
 bottom_solid_layers = 9
-bridge_acceleration = 300
+bridge_acceleration = 1000
 bridge_angle = 0
 bridge_flow_ratio = 0.8
 bridge_speed = 20
@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 25%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 20
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.10mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.10mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.12mm DETAIL Ender3.ini

@@ -1,7 +1,7 @@
 # generated by Slic3r Prusa Edition 1.40.1+win64 on 2018-08-21 at 02:49:24
 avoid_crossing_perimeters = 1
 bottom_solid_layers = 7
-bridge_acceleration = 300
+bridge_acceleration = 1000
 bridge_angle = 0
 bridge_flow_ratio = 0.8
 bridge_speed = 20
@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 20
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.15mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.15mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.16mm OPTIMAL Ender3.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 40
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm FAST 0.8 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.9
 first_layer_height = 0.2
@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.20mm NORMAL Ender3.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 40
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.24mm FAST Ender3.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 40
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.25mm VERY FAST MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.42
 first_layer_height = 0.2
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.28mm VERY FAST Ender3.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 40
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm 0.6 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.67
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.65
 first_layer_height = 0.3
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm FAST 0.8 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.9
 first_layer_height = 0.3
@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.30mm ULTRA FAST MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.42
 first_layer_height = 0.2
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.32mm ULTRA FAST Ender3.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.4 and printer_notes=~/.*PRINTER_NOT_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.45
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.45
 first_layer_height = 0.2
 first_layer_speed = 20
 gap_fill_speed = 40
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm 0.6 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.67
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.65
 first_layer_height = 0.3
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.35mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm 0.6 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.67
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.65
 first_layer_height = 0.4
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 27
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.40mm FAST 0.8 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.9
 first_layer_height = 0.4
@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano.ini

@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm 0.6 nozzle MK3.ini

@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.45mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.50mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 500
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 500
 perimeter_extruder = 1

PrusaSlicer/print/0.50mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.50mm FAST 0.8 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.9
 first_layer_height = 0.5
@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.55mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 20
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.55mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.60mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 18
 gap_fill_speed = 18
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.60mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.60mm FAST 0.8 nozzle MK3.ini

@@ -24,7 +24,7 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
+fill_pattern = gyroid
 first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.9
 first_layer_height = 0.6
@@ -49,7 +49,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.65mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 1.7
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 1.7
 first_layer_height = 0.4
 first_layer_speed = 16
 gap_fill_speed = 16
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/0.65mm Ender3 Volcano.ini

@@ -10,7 +10,7 @@ clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ and printer_notes=~/.*PRINTER_MODEL_ENDER3.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
 complete_objects = 0
-default_acceleration = 1500
+default_acceleration = 1000
 dont_support_bridges = 1
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 1
@@ -24,14 +24,14 @@ extruder_clearance_radius = 20
 extrusion_width = 0.9
 fill_angle = 45
 fill_density = 20%
-fill_pattern = grid
-first_layer_acceleration = 1500
+fill_pattern = gyroid
+first_layer_acceleration = 1000
 first_layer_extrusion_width = 0.84
 first_layer_height = 0.4
 first_layer_speed = 20
 gap_fill_speed = 30
 gcode_comments = 0
-infill_acceleration = 2000
+infill_acceleration = 1250
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.9
@@ -50,7 +50,7 @@ min_skirt_length = 4
 notes = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1

PrusaSlicer/print/Lithophanes 0.15mm 0.6 nozzle MK3 Volcano.ini

@@ -0,0 +1,110 @@
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-20 at 19:32:05 UTC
+avoid_crossing_perimeters = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 5
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.95
+bridge_speed = 25
+brim_width = 10
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_HAS_VOLCANO.*/ and nozzle_diameter[0]==0.6
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0.65
+external_perimeter_speed = 30
+external_perimeters_first = 0
+extra_perimeters = 0
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0.65
+fill_angle = 45
+fill_density = 99%
+fill_pattern = gyroid
+first_layer_acceleration = 1000
+first_layer_extrusion_width = 0.65
+first_layer_height = 0.3
+first_layer_speed = 20
+gap_fill_speed = 25
+gcode_comments = 0
+gcode_label_objects = 0
+infill_acceleration = 1250
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.7
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 45
+inherits = 0.30mm 0.6 nozzle MK3 Volcano
+interface_shells = 0
+layer_height = 0.15
+max_print_speed = 150
+max_volumetric_speed = 25
+min_skirt_length = 4
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+overhangs = 1
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.65
+perimeter_speed = 30
+perimeters = 10
+post_process = 
+print_settings_id = 
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 2
+skirt_height = 3
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 25
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0.7
+solid_infill_speed = 25
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 1
+support_material_contact_distance = 0.1
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.55
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_spacing = 0.2
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 50
+support_material_synchronize_layers = 0
+support_material_threshold = 55
+support_material_with_sheath = 0
+support_material_xy_spacing = 50%
+thin_walls = 0
+threads = 16
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 25
+top_solid_layers = 7
+travel_speed = 180
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 125
+xy_size_compensation = 0

PrusaSlicer/print/Lithophanes 0.20mm 0.6 nozzle MK3 Volcano.ini

@@ -0,0 +1,110 @@
+# generated by PrusaSlicer 2.1.1+win64 on 2019-12-21 at 02:50:16 UTC
+avoid_crossing_perimeters = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 5
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.95
+bridge_speed = 25
+brim_width = 10
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_HAS_VOLCANO.*/ and nozzle_diameter[0]==0.6
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 1
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0.61
+external_perimeter_speed = 30
+external_perimeters_first = 0
+extra_perimeters = 0
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0.61
+fill_angle = 45
+fill_density = 99%
+fill_pattern = gyroid
+first_layer_acceleration = 1000
+first_layer_extrusion_width = 0.61
+first_layer_height = 0.3
+first_layer_speed = 20
+gap_fill_speed = 25
+gcode_comments = 0
+gcode_label_objects = 0
+infill_acceleration = 1250
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.7
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 45
+inherits = 0.30mm 0.6 nozzle MK3 Volcano
+interface_shells = 0
+layer_height = 0.2
+max_print_speed = 150
+max_volumetric_speed = 25
+min_skirt_length = 4
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{filament_type[0]}{layer_height}mm_{total_weight}g_{nozzle_diameter[0]}n_{printer_model}_{print_time}.gcode
+overhangs = 1
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.61
+perimeter_speed = 30
+perimeters = 10
+post_process = 
+print_settings_id = 
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 2
+skirt_height = 3
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 25
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0.7
+solid_infill_speed = 25
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 1
+support_material_contact_distance = 0.1
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.55
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_spacing = 0.2
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 50
+support_material_synchronize_layers = 0
+support_material_threshold = 55
+support_material_with_sheath = 0
+support_material_xy_spacing = 50%
+thin_walls = 0
+threads = 16
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 25
+top_solid_layers = 6
+travel_speed = 180
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 125
+xy_size_compensation = 0