| 12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455 |
- # generated by PrusaSlicer 2.2.0+win64 on 2020-06-04 at 01:31:08 UTC
- bed_temperature = 115
- bridge_fan_speed = 40
- compatible_printers =
- compatible_printers_condition = printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
- compatible_prints =
- compatible_prints_condition =
- cooling = 1
- disable_fan_first_layers = 4
- end_filament_gcode = "; Filament-specific end gcode"
- extrusion_multiplier = 1
- fan_always_on = 0
- fan_below_layer_time = 30
- filament_colour = #3A80CA
- filament_cooling_final_speed = 3.4
- filament_cooling_initial_speed = 2.2
- filament_cooling_moves = 4
- filament_cost = 27.82
- filament_density = 1.04
- filament_deretract_speed = nil
- filament_diameter = 1.75
- filament_load_time = 0
- filament_loading_speed = 28
- filament_loading_speed_start = 3
- filament_max_volumetric_speed = 26
- filament_minimal_purge_on_wipe_tower = 15
- filament_notes = "List of materials tested with standard ABS print settings:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladec ABS"
- filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
- filament_retract_before_travel = nil
- filament_retract_before_wipe = nil
- filament_retract_layer_change = nil
- filament_retract_length = nil
- filament_retract_lift = nil
- filament_retract_lift_above = nil
- filament_retract_lift_below = nil
- filament_retract_restart_extra = nil
- filament_retract_speed = nil
- filament_settings_id = ""
- filament_soluble = 0
- filament_toolchange_delay = 0
- filament_type = ABS
- filament_unload_time = 0
- filament_unloading_speed = 90
- filament_unloading_speed_start = 100
- filament_vendor = (Unknown)
- filament_wipe = nil
- first_layer_bed_temperature = 110
- first_layer_temperature = 255
- inherits = Generic ABS
- max_fan_speed = 30
- min_fan_speed = 30
- min_print_speed = 15
- slowdown_below_layer_time = 20
- start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4}0.2{elsif printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6}0.02{elsif printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4}0.04{elsif printer_notes=~/.*PRINTER_FULLMODEL_ENDER3_DD_06.*/}0.02{else}0{endif} ; Filament gcode LA 1.5"
- temperature = 255
|
