| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172 |
- # generated by PrusaSlicer 2.0.0+win64 on 2019-06-19 at 02:08:45
- bed_shape = 0x0,250x0,250x210,0x210
- before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
- between_objects_gcode =
- cooling_tube_length = 5
- cooling_tube_retraction = 91.5
- default_filament_profile = "Prusament PLA"
- default_print_profile = 0.30mm QUALITY 0.6 nozzle MK3
- deretract_speed = 0
- end_gcode = G4 ; wait\nM221 S100\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200; home X axis\nM84 ; disable motors\nM300 S2600 P100; Beep
- extra_loading_move = -2
- extruder_colour = #FFFF00
- extruder_offset = 0x0
- gcode_flavor = marlin
- high_current_on_filament_swap = 0
- host_type = octoprint
- inherits = Original Prusa i3 MK3 0.6 nozzle
- layer_gcode = ;AFTER_LAYER_CHANGE\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
- machine_max_acceleration_e = 5000,5000
- machine_max_acceleration_extruding = 1250,1250
- machine_max_acceleration_retracting = 1250,1250
- machine_max_acceleration_x = 1000,960
- machine_max_acceleration_y = 1000,960
- machine_max_acceleration_z = 1000,1000
- machine_max_feedrate_e = 120,120
- machine_max_feedrate_x = 200,100
- machine_max_feedrate_y = 200,100
- machine_max_feedrate_z = 12,12
- machine_max_jerk_e = 1.5,1.5
- machine_max_jerk_x = 8,8
- machine_max_jerk_y = 8,8
- machine_max_jerk_z = 0.4,0.4
- machine_min_extruding_rate = 0,0
- machine_min_travel_rate = 0,0
- max_layer_height = 0.45
- max_print_height = 210
- min_layer_height = 0.1
- nozzle_diameter = 0.6
- parking_pos_retraction = 92
- print_host = http://octopimk3.local
- printer_model = MK3
- printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\nPRINTER_HAS_VOLCANO
- printer_settings_id =
- printer_technology = FFF
- printer_variant = 0.6
- printer_vendor =
- printhost_apikey = 852FD1ED19874F178DF73B325E3E8640
- printhost_cafile =
- remaining_times = 1
- retract_before_travel = 1
- retract_before_wipe = 0%
- retract_layer_change = 1
- retract_length = 0.8
- retract_length_toolchange = 4
- retract_lift = 0.6
- retract_lift_above = 0
- retract_lift_below = 209
- retract_restart_extra = 0
- retract_restart_extra_toolchange = 0
- retract_speed = 35
- serial_port =
- serial_speed = 250000
- silent_mode = 1
- single_extruder_multi_material = 0
- start_gcode = ; Last updated 20190218\nM115 U3.7.1 ; tell printer latest fw version\n\nM907 E400; Set current for E\nM907 Y500; Set current for Y\n;G4 S2; Wait 2 seconds for apply current\nM300 S40 P20 ; chirp\n\n; Disable all heaters\nM104 S0 ; set extruder temp\nM140 S0 ; turn off heatbed\nM106 S255; Fan ON max\n\n; Cooldown PINDA if needed\nG90\nG1 X0 Z100 ; this is a good PINDA heating position\nM860 S35; Wait for pinda temp >=\n\n; Set initial warmup temps\nM104 S140 ; set extruder no-ooze temp\nM140 S{max(first_layer_bed_temperature[0],60)}\n; Nozzle warmup routine\n\nG28 W ; home all without mesh bed level\nG0 X125 Y200 Z100.0 F10200 ; raise nozzle and present bed for cleaning\nM109 ; wait for extruder no-ooze warmup temp before mesh bed leveling, cool hot PINDA\nM106 S0; Fan OFF\n\n; PINDA warmup routine\n;M300 S40 P10 ; chirp\n;G0 X125 Y105 Z0.10 F10200; PINDA warming position\nG28 W; PINDA warming position\nM860 S35 ; wait for PINDA temp to stabilize\n;M300 S40 P10 ; chirp\n\n;G28 W ; home all without mesh bed level\nM140 S[first_layer_bed_temperature] ; set bed final temp\nG80 ; mesh bed leveling\n\n; Final warmup routine\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\n\n;G4 S180; Wait 3 minutes for stabilize bed temp, use for ABS large prints\n\n; Prime line routine\n;M300 S25 P10 ; chirp\nM83 ; extruder relative mode\nM900 K0; Disable LA for prime line\nG92 E0.0 ; reset extrusion distance\nG1 Y-3.0 F1000.0 ; go outside print area\nG1 E2 F1000 ; de-retract and push ooze\nG1 X20.0 E6 F1000.0 ; fat 20mm intro line @ 0.30\nG1 X60.0 E3.2 F1000.0 ; thin +40mm intro line @ 0.08\nG1 X100.0 E6 F1000.0 ; fat +40mm intro line @ 0.15\nG1 E-0.8 F2100; retract to avoid stringing\nG1 X99.0 E0 F1000.0 ; -1mm intro line @ 0.00\nG1 X110.0 E0 F1000.0 ; +10mm intro line @ 0.00\nG1 E0.6 F1500; de-retract\nG92 E0.0 ; reset extrusion distance\n; Final print adjustments\n;M92 E282.54 ; adjust extrusion ratio\n;M221 S{if layer_height==0.05}100{else}95{endif}
- toolchange_gcode =
- use_firmware_retraction = 0
- use_relative_e_distances = 1
- use_volumetric_e = 0
- variable_layer_height = 1
- wipe = 1
- z_offset = 0
|
