# generated by PrusaSlicer 2.1.1+win64 on 2020-03-04 at 06:26:14 UTC
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
between_objects_gcode = 
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = Generic PLA Volcano
default_print_profile = 0.30mm 0.6 nozzle MK3 Volcano
deretract_speed = 0
end_gcode = G4 ; wait\nM221 S100\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200; home X axis\nM84 ; disable motors\nM300 S2600 P100; Beep
extra_loading_move = -2
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = Original Prusa i3 MK3 0.6 nozzle
layer_gcode = ;AFTER_LAYER_CHANGE\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 1250,1250
machine_max_acceleration_retracting = 1250,1250
machine_max_acceleration_x = 1000,960
machine_max_acceleration_y = 1000,960
machine_max_acceleration_z = 1000,1000
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 200,100
machine_max_feedrate_y = 200,100
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 4.5,4.5
machine_max_jerk_x = 8,8
machine_max_jerk_y = 8,8
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.45
max_print_height = 210
min_layer_height = 0.15
nozzle_diameter = 0.6
parking_pos_retraction = 92
print_host = http://octopimk3.local
printer_model = MK3
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\nPRINTER_HAS_VOLCANO
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.6
printer_vendor = 
printhost_apikey = 852FD1ED19874F178DF73B325E3E8640
printhost_cafile = 
remaining_times = 1
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 4
retract_lift = 0.6
retract_lift_above = 0
retract_lift_below = 209
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
serial_port = 
serial_speed = 250000
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = ; Last updated 04/03/2020\nM862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.8.1 ; tell printer latest fw version\n\n\nM907 E400; Set current for E\nM907 Y500; Set current for Y\nM300 S40 P20 ; chirp\n\n; Disable all heaters\nM104 S0 ; set extruder temp\nM140 S0 ; turn off heatbed\nM106 S255; Fan ON max\n\n; Set initial warmup temps\nM104 S140 ; set extruder no-ooze temp\nM140 S[first_layer_bed_temperature] ; set bed final temp\n; Nozzle warmup routine\n\nG90\nG0 X125 Y200 Z100.0 F10200 ; raise nozzle and present bed for cleaning\nM109 ; wait for extruder no-ooze warmup temp before mesh bed leveling, cool hot PINDA\nM106 S0; Fan OFF\n\nG80 ; mesh bed leveling\n\n; Final warmup routine\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\n\n;G4 S180; Wait 3 minutes for stabilize bed temp, use for ABS large prints\n\n; Prime line routine\n;M300 S25 P10 ; chirp\nM83  ; extruder relative mode\nM900 K0; Disable LA for prime line\nG92 E0.0 ; reset extrusion distance\nG1 Y-3.0 F1000.0 ; go outside print area\nG1 E2 F1000 ; de-retract and push ooze\nG1 X20.0 E6  F1000.0 ; fat 20mm intro line @ 0.30\nG1 X60.0 E3.2  F1000.0 ; thin +40mm intro line @ 0.08\nG1 X100.0 E6  F1000.0 ; fat +40mm intro line @ 0.15\nG1 E-0.8 F2100; retract to avoid stringing\nG1 X99.0 E0 F1000.0 ; -1mm intro line @ 0.00\nG1 X110.0 E0 F1000.0 ; +10mm intro line @ 0.00\nG1 E0.6 F1500; de-retract\nG92 E0.0 ; reset extrusion distance\n; Final print adjustments\n;M92 E282.54 ; adjust extrusion ratio\n;M221 S{if layer_height==0.05}100{else}95{endif}
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0