Updated and fix "Machine Limits"

PrusaSlicer/filament/ColorFabb nGen Volcano.ini

@@ -0,0 +1,43 @@
+# generated by PrusaSlicer 2.0.0+win64 on 2019-07-18 at 16:41:54
+bed_temperature = 90
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_HAS_VOLCANO.*/
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 3
+end_filament_gcode = "; Filament-specific end gcode"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 10
+filament_colour = #FF8000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 21.2
+filament_density = 1.2
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 24
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = NGEN
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+first_layer_bed_temperature = 85
+first_layer_temperature = 240
+inherits = ColorFabb nGen
+max_fan_speed = 50
+min_fan_speed = 35
+min_print_speed = 15
+slowdown_below_layer_time = 20
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}24{else}45{endif} ; Filament gcode"
+temperature = 230

PrusaSlicer/print/0.04mm ULTRA DETAIL Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.05mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.06mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.08mm VERY DETAIL Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.10mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.10mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.10mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.12mm DETAIL Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.15mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.15mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.15mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.16mm OPTIMAL Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.20mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.20mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.20mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.20mm FAST 0.8 nozzle MK3.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.20mm NORMAL Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.24mm FAST Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.25mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.25mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.25mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.25mm VERY FAST MK3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.28mm VERY FAST Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.30mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.30mm 0.6 nozzle MK3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.30mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.30mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.30mm FAST 0.8 nozzle MK3.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.30mm ULTRA FAST MK3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.32mm ULTRA FAST Ender3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.45

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.35mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.35mm 0.6 nozzle MK3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.35mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.35mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-22 at 17:31:51
+# generated by PrusaSlicer 2.0.0+win64 on 2019-07-18 at 15:38:36
 avoid_crossing_perimeters = 0
 bottom_fill_pattern = rectilinear
 bottom_solid_layers = 3
@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.40mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.40mm 0.6 nozzle MK3.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.40mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.40mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.40mm FAST 0.8 nozzle MK3.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano 0.8mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.8

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano 1.0mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano 1.2mm Extrusion.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.45mm 0.6 nozzle MK3 Volcano.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.65

PrusaSlicer/print/0.45mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.45mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.50mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 500
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.50mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.50mm FAST 0.8 nozzle MK3.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.55mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.55mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.60mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.60mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.60mm FAST 0.8 nozzle MK3.ini

@@ -50,7 +50,7 @@ notes =
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/print/0.65mm Ender3 Volcano 1.7mm Extrusion.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 1.7

PrusaSlicer/print/0.65mm Ender3 Volcano.ini

@@ -51,7 +51,7 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]_[filament_type][layer_height]mm.gcode
-overhangs = 0
+overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.9

PrusaSlicer/printer/Creality Ender-3 DirectDrive Volcano 0.6 Nozzle + BLTouch RECALL.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-22 at 17:44:25
+# generated by PrusaSlicer 2.0.0+win64 on 2019-07-31 at 02:43:01
 bed_shape = 0x0,230x0,230x203,0x203
 before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 between_objects_gcode = 
@@ -14,21 +14,21 @@ extruder_offset = 0x0
 gcode_flavor = marlin
 high_current_on_filament_swap = 0
 host_type = octoprint
-inherits = 
+inherits = Original Prusa i3 MK3
 layer_gcode = ;AFTER_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 machine_max_acceleration_e = 5000,5000
-machine_max_acceleration_extruding = 1250,1000
-machine_max_acceleration_retracting = 7000,1000
-machine_max_acceleration_x = 1000,500
-machine_max_acceleration_y = 1000,500
-machine_max_acceleration_z = 100,100
-machine_max_feedrate_e = 120,50
-machine_max_feedrate_x = 500,200
-machine_max_feedrate_y = 500,200
-machine_max_feedrate_z = 15,10
-machine_max_jerk_e = 5,5
-machine_max_jerk_x = 10,10
-machine_max_jerk_y = 10,10
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 1000,1000
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 1.5,1.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
 machine_max_jerk_z = 0.4,0.4
 machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
@@ -51,7 +51,7 @@ retract_before_travel = 1
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 0.8
-retract_length_toolchange = 10
+retract_length_toolchange = 4
 retract_lift = 0.6
 retract_lift_above = 0
 retract_lift_below = 236

PrusaSlicer/printer/Creality Ender-3 DirectDrive Volcano 0.6 Nozzle + BLTouch.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-06-22 at 15:46:09
+# generated by PrusaSlicer 2.0.0+win64 on 2019-07-31 at 02:39:16
 bed_shape = 0x0,230x0,230x203,0x203
 before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 between_objects_gcode = 
@@ -14,21 +14,21 @@ extruder_offset = 0x0
 gcode_flavor = marlin
 high_current_on_filament_swap = 0
 host_type = octoprint
-inherits = 
+inherits = Original Prusa i3 MK3
 layer_gcode = ;AFTER_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 machine_max_acceleration_e = 5000,5000
-machine_max_acceleration_extruding = 1250,1000
-machine_max_acceleration_retracting = 1250,1000
-machine_max_acceleration_x = 1000,500
-machine_max_acceleration_y = 1000,500
-machine_max_acceleration_z = 100,100
-machine_max_feedrate_e = 120,50
-machine_max_feedrate_x = 500,200
-machine_max_feedrate_y = 500,200
-machine_max_feedrate_z = 15,10
-machine_max_jerk_e = 5,5
-machine_max_jerk_x = 10,10
-machine_max_jerk_y = 10,10
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 1000,1000
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 1.5,1.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
 machine_max_jerk_z = 0.4,0.4
 machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
@@ -51,7 +51,7 @@ retract_before_travel = 1
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 0.8
-retract_length_toolchange = 10
+retract_length_toolchange = 4
 retract_lift = 0.6
 retract_lift_above = 0
 retract_lift_below = 236

PrusaSlicer/printer/Creality Ender-3 Volcano 0.8 Nozzle + BLTouch RECALL.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-05-23 at 00:47:39
+# generated by PrusaSlicer 2.0.0+win64 on 2019-07-31 at 02:43:15
 bed_shape = 0x0,220x0,220x220,0x220
 before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 between_objects_gcode = 
@@ -14,21 +14,21 @@ extruder_offset = 0x0
 gcode_flavor = marlin
 high_current_on_filament_swap = 0
 host_type = octoprint
-inherits = 
+inherits = Original Prusa i3 MK3
 layer_gcode = ;AFTER_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 machine_max_acceleration_e = 5000,5000
-machine_max_acceleration_extruding = 1500,1000
-machine_max_acceleration_retracting = 7000,1000
-machine_max_acceleration_x = 1500,500
-machine_max_acceleration_y = 1500,500
-machine_max_acceleration_z = 100,100
-machine_max_feedrate_e = 50,50
-machine_max_feedrate_x = 500,200
-machine_max_feedrate_y = 500,200
-machine_max_feedrate_z = 15,15
-machine_max_jerk_e = 5,5
-machine_max_jerk_x = 20,10
-machine_max_jerk_y = 20,10
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 1000,1000
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 1.5,1.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
 machine_max_jerk_z = 0.4,0.4
 machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
@@ -51,7 +51,7 @@ retract_before_travel = 1.5
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 3
-retract_length_toolchange = 10
+retract_length_toolchange = 4
 retract_lift = 0.6
 retract_lift_above = 0
 retract_lift_below = 234

PrusaSlicer/printer/Creality Ender-3 Volcano 0.8 Nozzle + BLTouch.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.0.0+win64 on 2019-05-23 at 00:47:21
+# generated by PrusaSlicer 2.0.0+win64 on 2019-07-31 at 02:43:11
 bed_shape = 0x0,220x0,220x220,0x220
 before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 between_objects_gcode = 
@@ -14,21 +14,21 @@ extruder_offset = 0x0
 gcode_flavor = marlin
 high_current_on_filament_swap = 0
 host_type = octoprint
-inherits = 
+inherits = Original Prusa i3 MK3
 layer_gcode = ;AFTER_LAYER_CHANGE\nG92 E0.0\n;Layer [layer_num]\n;[layer_z]mm\n;Printing layer [layer_num] at [layer_z]mm\n\n
 machine_max_acceleration_e = 5000,5000
-machine_max_acceleration_extruding = 1500,1000
-machine_max_acceleration_retracting = 5000,1000
-machine_max_acceleration_x = 1500,500
-machine_max_acceleration_y = 1500,500
-machine_max_acceleration_z = 100,100
-machine_max_feedrate_e = 50,50
-machine_max_feedrate_x = 500,200
-machine_max_feedrate_y = 500,200
-machine_max_feedrate_z = 15,5
-machine_max_jerk_e = 5,5
-machine_max_jerk_x = 20,10
-machine_max_jerk_y = 20,10
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 1000,1000
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 1.5,1.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
 machine_max_jerk_z = 0.4,0.4
 machine_min_extruding_rate = 0,0
 machine_min_travel_rate = 0,0
@@ -51,7 +51,7 @@ retract_before_travel = 1.5
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 4
-retract_length_toolchange = 10
+retract_length_toolchange = 4
 retract_lift = 0.6
 retract_lift_above = 0
 retract_lift_below = 239